Are Solder Ring Fittings Any Good

I would suggest you put flux on the edge of fitting as you solder and use gentle heat and you should see a ring of solder appearing. I would never put one where it was not visible or even where it would be difficult to replace it some time in the future.

Pin On Plumbing

Dlh TX i dont like either one.

Are solder ring fittings any good. Soldering protects your rings Any time you wear two rings on one finger they are going to rub against one another. Also heat the pipe and fitting over the entire fitting not just the bit you are soldering. For a list of available solder ring fittings please see here- Solder ring fittings.

I would recommend solder ring fittings for any DIY task As most of the hard work is pre-done simply cut and de-bur the copper tube clean and flux then apply your heat gunBlowtorch. Leaks from Solder-ring fittings. These types of fittings are very popular in the UK an.

In this video I use some Yorkshire fittings often known as solder ring fittings or capillary fittings. On solder ring fittings I apply the flame to the pipe adjacent to the fitting and wait until the solder is drawn out and forms a ring around the fitting. Over time this corrodes the rings and can lead to excessive ring maintenance.

Ive soldered about 17 joints with one failure. If solder drips out there will not be enough solder left to seal the joint properly. So to answer your question they are not as permanent as solder or flare for that matter connections.

It can be used with all types and sizes of soft solder fittings for applications including gas and is char-resistant to normal heating levels of 250ºC. Solder ring is certainly the more expensive method - from toolstation - 60pfitting for 22mm equal t and 140 for solder ring. It can be used with all types and sizes of soft solder fittings for applications including gas and is char-resistant to normal heating levels of 250ºC.

Solder Ring fittings can only be used on copper pipe and are no good for use on plastic pipe. I recently put in the pipework for a central heating system. The ring leaves a void and the pre soldered do not fit good take out the solder and they are really lose - - - - - - - PLUMBERS Protecting The Health Of The Nation.

Cleaning the pipe is good pratice but with most modern self cleaning fluxes you can get away without cleaning although I wouldnt recommend it. I CAN solder. Capillary action will cause the solder to be sucked-in to the fitting due to the solders very high surface tension.

Just remember to clean the pipe ends well and use a flux. Not because we were seeing a lot of solder joints failing. As you know this will cause a leak in a short amount of time if not immediately.

Ad Find China Manufacturers Of Solder. Solder Ring fittings are the more expensive than the Endfeed but much easier to install. Pre soldered copper fittings.

Can you use solder ring fittings on gas. Personally I find the simple cheap end feed solder fittings the easiest. When I pressure tested each half of the system flow and then return with rad valves all closed I got leaks on 3 different.

I think solder ring fittings would be more reliable with properly flowing solder especially in tight spaces where you cannot see the other side and if they are about the same price why not use solder ring fittings. To solder the joints a blowtorch or a heat gun will be needed. I used solder-ring fittings for all the joints.

Ad Find China Manufacturers Of Solder. Solder ring fittings are more expensive than end feed fittings so if you are working on a large project you might want to use end feed fittings. Id use normal fittings Ive never used solder ring but believe are more prone to leaking.

Any press or grip fitting with just a small o-ring seal make you wonder. End feed is also neater in many peoples view - especially when no excess solder is used and the solder is put on from the back. These fittings have a ring of solder built into the fitting which melts at temperature and joins the pipe to the fitting.

I can solder and next time Id do better because Ive learned more about it but Id use solder ring fittings. There is a rubber O-ring inside the fitting. Soldering the rings together is probably a good choice.

They are also good if you need to get around hot permit work. Add a little solder with the solder wire end dipped in flux and that proves solder is melting and flowing. I used 22mm pipes for the main run and teed off with 15mm to each rad.

I always use more than than the recommended amount of solder and brush with flux after soldering to be sure has run. In respect to this do solder ring fittings need flux. If there is not enough room around the fitting to get a good solder or if it is difficult to reach it is likely that you will not be able to achieve a good solder.

For example if your ring is white gold youll have to get the ring rhodium plated more often to keep it in sparkling condition. I think press fittings were designed as time savers repair fittings etc. Fitting ANY movement can cause a compression joint to leak.

But I wont be using solder ring fittings because they are hard to get.

Pin On Copper Pipe Fittings