Abs Tone Ring Removal

Despite the proper gap signals from the sensors will be incorrect if the wheel bearings are worn or loose. Strike the end of the locking pliers with a mallet to lift the ring off of the hub.

Pin On Useful Tips

Consolidated Metco has a universal ABS tone ring installation tool part number 107119 available for front drive and trailer hubs.

Abs tone ring removal. Using 2 screw drivers under lip of ring. Prior to assembly remove all corrosion and contamination from the hub surface where the tone ring seats. Center the corresponding diameter of the tool onto the ABS ring.

If the tone rings are the cause those problems will not be detected until the car is moving sometimes as much as a few yards up to a mile or more. Place the ABS ring onto the hub. This tool is designed to be assembled using a standard seal installation tool handle.

ABS TONE RING INSTALLATION. Find many great new used options and get the best deals for EASY PULL ABS SENSOR TONE RING REMOVER TOOL for Toyota trucks USA 43517-35010 at the. The better you clean it and remove the loose rust powder afterword the better.

For steer axle hubs make sure the inside diameter ﬂ ange is up Figure 3. But keep in mind that the tone ring is magnetic and rust is ferrous. If the tone ring seat is damaged replace the hub.

A worn cracked or warped tone ring wont produce a usable signal. Work your way around the hub to remove the ring. Strike the end of the locking pliers with a mallet to lift the ring off of the hub.

Using a torch heat ring until you can spin the ring around on the hub using a flat blade screw driver. Prior to assembly remove all corrosion and contamination from. Even a small chip in the tone wheel can cause problems so you should not use a pry bar or hammer to remove a half-shaft from a steering knuckle.

Remove seal and bearing from hub. Tone ring performance can be significantly reduced by contamination. This is a simple video on how to remove the tone ring ABS Ring Reluctor Ring from the CV axle on a Dodge Chrysler or Jeep which commonly have bad CV a.

If however the tone ring is bolted to the rotor just use an allen wrench to remove the bolts and then put it on the new rotor. If this were due to an electrical problem as in a cut wire to a sensor that would be detected as soon as you turned on the ignition switch and the ABS Computer went through its six-second self test. This tool is designed for stamped steel ABS tone rings only.

After removing the ENTIRE tone ring start cleaning and removing rust using the sandpaper scotchbrite wire wheel etc. ABS Tone Ring Removal For drive and trailer hubs grip the edge of the ring with locking pliers directly in front of a wheel bolt. Drive axle and trailer tone rings can be removed by gripping the ring with a pair of locking pliers and prying against the head of a wheel stud to lift the ring off the hub.

If the abs tone ring needs to be removed to gain access to the rotor then use a torch to heat it until it spins freely and pop it off with a couple of screw drivers. How to Replace ABS Tone Rings on ConMet Hub Assemblies ABS Tone Ring Removal For drive and trailer hubs grip the edge of the ring with locking pliers directly in front of a wheel bolt. Consolidated Metco has a universal ABS tone ring installation tool part number 107119 available for front drive and trailer hubs.

Work your way around the ring to prevent cocking Figure 2.

Abs Tone Ring Replacement Youtube

Https Www Conmet Com Wp Content Uploads 2014 06 How To Presentation Abs Rings 6 2014 Pdf

Help Replacing Rear Abs Tone Ring Scoobynet Com Subaru Enthusiast Forum

How To Remove And Replace Abs Tone Rings

Pin On Hair Removal Permanent

Rear Abs Sensor Removal Right Way And Wrong Way Impreza Resto Com

Replace 2008 Ford Escape Front Abs Tone Ring Youtube

Pin On Car Repairs

Abs Lamp Lit Wheel Speed Sensor No Signal Code Wheel Speed Sensor Tone Ring Split Rust On Drive Axle Breaks Tone Ring T Lamp Light Auto Repair Mirror Table